knife making steel and its properties
PERFORMANCE OF STEEL
– Best knife making steel –
What is it we’re looking for in a knife making steel, anyway? Well, what we are looking for is strength, toughness, wear resistance, and edge holding. Sometimes, we’re also looking for stain resistance.
Just like it sounds, wear resistance is the ability to withstand abrasion. Generally speaking, the amount, type, and distribution of carbides within the steel is what determines wear resistance.
The ability to take a load without permanently deforming. For many types of jobs, strength is extremely important. Any time something hard is being cut, or there’s lateral stress put on the edge, strength becomes a critical factor. In steels, strength is directly correlated with hardness — the harder the steel, the stronger it is. Note that with the Rockwell test used to measure hardness in a steel, it is the hardness of the steel matrix being measured, not the carbides. This, it’s possible for a softer, weaker steel (measuring low on the Rockwell scale) to have more wear resistance than a harder steel. S60V, even at 56 Rc, still has more and harder carbides than ATS-34 at 60 Rc, and thus the S60V is more wear resistant, while the ATS-34 would be stronger.
The ability to take an impact without damage, by which we mean, chipping, cracking, etc. Toughness is obviously important in jobs such as chopping, but it’s also important any time the blade hits harder impurities in a material being cut (e.g., cardboard, which often has embedded impurities).
The knifemaker will be making a tradeoff of strength versus toughness. Generally speaking, within the hardness range that the steel performs well at, as hardness increases, strength also increases, but toughness decreases. This is not always strictly true, but as a rule of thumb is generally accurate. In addition, it is possible for different heat treat formulas to leave the steel at the same hardness, but with properties such as toughness, wear resistance, and stain resistance significantly differing.
Stain resistance (rust resistance)
The ability to withstand rust (oxidation). Obviously, this property can be helpful in corrosive environments, such as salt water. In addition, some types of materials are acidic (e.g, some types of foods), and micro-oxidation can lead to edge loss at the very tip of the edge, over a small amount of time. In “stainless” cutlery steels, stain resistance is most affected by free chromium — that is, chromium that is not tied up in carbides. So, the more chromium tied up in carbides, the less free chromium there is, which means more wear resistance but less stain resistance.
The ability of a blade to hold an edge. Many people make the mistake of thinking wear resistance and edge holding are the same thing. Most assuredly, it is not; or rather, it usually is not. Edge holding is job-specific. That is, edge holding is a function of wear resistance, strength, and toughness. But different jobs require different properties for edge holding.
For example, cutting through cardboard (which often has hard embedded impurities), toughness becomes extremely important, because micro-chipping is often the reason for edge degradation. Whittling very hard wood, strength becomes very important for edge-holding, because the primary reason for edge degradation is edge rolling and impaction. Wear resistance becomes more important for edge holding when very abrasive materials, such as carpet, are being cut. And for many jobs, where corrosion- inducing materials are contacted (such as food prep), corrosion can affect the edge quickly, so corrosion resistance has a role to play as well.
There are other properties that significantly effect how a knife making steel performs:
Ability to take an edge
Some steels just seem to take a much sharper edge than other steels, even if sharpened the exact same way. Finer-grained steels just seem to get scary sharp much more easily than coarse-grained steels, and this can definitely effect performance. Adding a bit of vanadium is an easy way to get a fine-grained steels. In addition, an objective of the forging process is to end up with a finer-grained steel. So both steel choice,and the way that steel is handled, can effect cutting performance.
Cleaner, purer steels perform better than dirtier, impure steels. The cleaner steel will often be stronger and tougher, having less inclusions. High quality processes used to manufacture performance steel include the Argon/Oxygen/Decarburization (AOD) process, and for even purer steel, the Vacuum Induction Melting/Vacuum Arc Remelting (VIM/VAR) process, often referred to as double vacuum melting or vacuum re-melting.
Some steels seem to cut aggressively even when razor polished. For these steels, even when they’re polished for push-cutting, their carbides form a kind of “micro serrations” and slice aggressively.
Knowing the uses you’ll put your knife to, and exactly how those uses cause edge degradation, will allow you to make a much better choice of steel, if you generally understand steel properties.
The properties of different steels will be laid out below.
But in your search for the knife with the “best knife making steel” for your uses, I always suggest you ask the makers of the knives you’re considering which steels they would use. The knifemaker will usually know which steels he can make perform the best. And as pointed out above, heat treat is absolutely critical to bringing out the best in a steel. A maker who has really mastered one particular steel (e.g., Dozier and D2) might be able to make that steel work well for many different uses. So never go just by charts and properties; make sure you also consider what the knifemaker can do with the steel.
ELEMENTS OF STEEL – Knife making steel –
At its most simple, steel is iron with carbon in it. Other alloys are added to make the steel perform differently. Here are the important knife making steel alloys in alphabetical order, and some sample steels that contain those alloys:
Present in all steels, it is the most important hardening element. Also increases the strength of the steel but, added in isolation, decreases toughness. We usually want knife-grade steel to have >.5% carbon, which makes it “high-carbon” steel.
Added for wear resistance, hardenability, and (most importantly) for corrosion resistance. A steel with at least 13% chromium is typically deemed “stainless” steel, though another definition says the steel must have at least 11.5% *free* chromium (as opposed to being tied up in carbides) to be considered “stainless”. Despite the name, all steel can rust if not maintained properly. Adding chromium in high amounts decreases toughness. Chromium is a carbide-former, which is why it increases wear resistance.
An important element, manganese aids the grain structure, and contributes to hardenability. Also strength & wear resistance. Improves the steel (e.g., deoxidizes) during the steel’s manufacturing (hot working and rolling). Present in most cutlery steel except for A2, L-6, and CPM 420V.
A carbide former, prevents brittleness & maintains the steel’s strength at high temperatures. Present in many steels, and air-hardening steels (e.g., A2, ATS-34) always have 1% or more molybdenum — molybdenum is what gives those steels the ability to harden in air.
Adds toughness. Present in L-6 and AUS-6 and AUS-8. Nickel is widely believed to play a role in corrosion resistance as well, but this is probably incorrect.
Present in small amounts in most steels, phosphorus is a essentially a contaminant which reduces toughness.
Contributes to strength. Like manganese, it makes the steel more sound while it’s being manufactured.
Typically not desirable in cutlery steel, sulfur increases machinability but decreases toughness.
A carbide former, it increases wear resistance. When combined properly with chromium or molybdenum, tungsten will make the steel to be a high-speed steel. The high-speed steel M2 has a high amount of tungsten. The strongest carbide former behind vanadium.
Contributes to wear resistance and hardenability, and as a carbide former (in fact, vanadium carbides are the hardest carbides) it contribute to wear resistance. It also refines the grain of the steel, which contributes to toughness and allows the blade to take a very sharp edge. A number of steels have vanadium, but M2, Vascowear, and CPM T440V and 420V (in order of increasing amounts) have high amounts of vanadium. BG-42’s biggest difference with ATS-34 is the addition of vanadium.
TYPES OF STEEL – Knife making steel –
i) Non-stainless Steels (carbon, alloy, and tool steels):
These steels are the steels most often forged. Stainless steels can be forged (guys like Sean McWilliams do forge stainless), but it is very difficult. In addition, carbon steels can be differentially tempered, to give a hard edge-holding edge and a tough springy back. Stainless steels are not differentially tempered. Of course, carbon steels will rust faster than stainless steels, to varying degrees. Carbon steels are also often a little bit less of a crap shoot than stainless steels — I believe all the steels named below are fine performers when heat treated properly.
In the AISI steel designation system, 10xx is carbon steel, any other steels are alloy steels. For example, the 50xx series are chromium steels.
In the SAE designation system, steels with letter designations (e.g., W-2, A2) are tool steels.
There is an ASM classification system as well, but it isn’t seen often in the discussion of cutlery steels, so I’ll ignore it for now. Often, the last numbers in the name of a steel are fairly close to the steel’s carbon content. So 1095 is ~.95% carbon. 52100 is ~1.0% carbon. 5160 is ~.60% carbon.
D2 is sometimes called a “semi-stainless“. It has a fairly high chrome content (12%), but not high enough to classify it as stainless. More stain resistant than the carbon steels mentioned above, however. It has excellent wear resistance. D2 is much tougher than the premium stainless steels like ATS-34, but not as tough as many of the other non-stainless steels mentioned here. The combination of great wear resistance, almost-stainlessness, and good toughness make it a great choice for a number of knife styles. Bob Dozier is one maker who uses D2. Benchmade has begun using D2 in its Axis AFCK.
Ref – D2 Steel Composition.
A “high-speed steel“, it can hold its temper even at very high temperatures, and as such is used in industry for high-heat cutting jobs. It is slightly tougher, and is slightly more wear resistant, than D2. However, M2 rusts easily. Benchmade has started using M2 in one of their AFCK 710 variations.
Ref – M2 Steel Composition. M2 steel knives are discontinued by Benchmade.
An excellent air-hardening tool steel, it is tougher than D2 and M2, with less wear resistance . As an air-hardening steel, don’t expect it to be differentially tempered. Its good toughness makes it a frequent choice for combat knives. Chris Reeve and Phil Hartsfield both use A2.
Ref – A2 Steel Composition.
This is a steel very popular with forgers, as it has the reputation for being “forgiving”. It is an excellent knife making steel, that takes and holds an edge superbly, and is tough (although not as tough as, say, 5160). It rusts easily, however. Randall Knives uses O1, so does Mad Dog Knives.
Ref – O1 Steel Composition.
Reasonably tough and holds an edge well, due to its .2% vanadium content. Most files are made from W-1, which is the same as W-2 except for the vanadium content (W-1 has no vanadium).
Ref – W2 Steel Composition.
1095 (and 1084, 1070, 1060, 1050, etc.) Many of the 10-series steels for cutlery, though 1095 is the most popular for knife making steel. When you go in order from 1095-1050, you generally go from more carbon to less, from more wear resistance to less wear resistance, and tough to tougher to toughest. As such, you’ll see 1060 and 1050, used often for swords.
For knives, 1095 is sort of the “standard” carbon steel, not too expensive and performs well. It is reasonably tough and holds an edge well, and is easy to sharpen. It rusts easily. This is a simple knife making steel, which contains only two alloying elements: .95% carbon and .4% manganese. The various Kabars are usually 1095 with a black coating.
Ref – 1095 vs. 1084 vs. 1070 vs. 1060 vs. 1050 Steel Composition Comparison.
Carbon V is a trademarked term by Cold Steel, and as such is not necessarily one particular kind of steel; rather, it describes whatever steel Cold Steel happens to be using, and there is an indication they do change steels from time to time. Carbon V performs roughly between 1095-ish and O1-ish, in my opinion, and rusts like O1 as well. I’ve heard rumors that Carbon V is O1 (which I think is unlikely) or 1095. Numerous industry insiders insist it is 0170-6. Some spark tests done by a rec.knives reader seem to point the finger at 50100-B. Since 50100-B and 0170-6 are the same steel (see below), this is likely the current Carbon V.
0170-6 – 50100-B
These are different designations for the same steel: 0170-6 is the steel makers classification, 50100-B is the AISI designation. A good chrome-vanadium steel that is somewhat similar to O1, but much less expensive. The now-defunct Blackjack made several knives from O170-6, and Carbon V may be 0170-6. 50100 is basically 52100 with about 1/3 the chromium of 52100, and the B in 50100-B indicates that the steel has been modified with vanadium, making this a chrome-vanadium steel.
Ref – 0170-6 – 50100-B Steel Composition.
A band saw steel that is very tough and holds an edge well, but rusts easily. It is, like O1, a forgiving steel for the forger. If you’re willing to put up with the maintenance, this may be one of the very best steels available for cutlery, especially where toughness is desired. In a poll on the knifemakers email list back in the 1990s, when asked what the makers would use for their personal knife, L-6 emerged as the top choice.
Ref – L6 Steel Composition.
A steel popular with forgers, it is popular now for a variety of knife styles, but usually bigger blades that need more toughness. It is essentially a simple spring steel with chromium added for hardenability. It has good wear resistance, but is known especially for its outstanding toughness. This steel performs well over a wide range of hardnesses, showing great toughness when hardened in the low 50s Rc for swords, and hardened up near the 60s for knives needing more edge holding.
Ref – 5160 Steel Composition.
Formerly a ball-bearing steel, and as such previously only used by forgers, it’s available in bar stock now. It is similar to 5160 (though it has around 1% carbon vs. 5160 ~.60%), but holds an edge better. It is less tough than 5160. It is used often for hunting knives and other knives where the user is willing to trade off a little of 5160’s toughness for better wear resistance.
However, with the continued improvement of 52100 heat treat, this steel is starting to show up in larger knives and showing excellent toughness. A modified 52100 is being used by Jerry Busse in his lower-cost production line, and such high-performance knife making steel luminaries as Ed Fowler strongly favor 52100.
Ref – 52100 Steel Composition.
Crucible’s somewhat-stain-resistant 10V provides incredible wear resistance with D2-class toughness. It is an outstanding choice when maximum wear resistance is desired, but not super toughness.
Ref – CPM 10V Steel Composition.
CPM’s incredibly tough 3V gives excellent wear resistance and good stain resistance as well, although when it does stain, it is said to pit rather than surface rust. When maximum toughness is desired, with very good wear resistance, 3V is a great choice. Ref – CPM 3V Steel Composition.
INFI is currently only used by Jerry Busse. In place of some of the carbon (INFI contains 0.50% carbon), INFI has nitrogen. The result is a non-stainless steel that is nevertheless extremely stain resistant (informally reported at close to D2, or even better), incredibly tough for a high-alloy ingot steel, and with extremely good wear resistance.
Ref – INFI Steel Composition.
A very hard-to-find steel, with a high vanadium content. It is extremely difficult to work and very wear-resistant. It is out of production.
Ref – Vascowear Steel Composition.
ii) Stainless Steels
Remember that all steels can rust. But the following steels, by virtue of their > 13% chromium, have much more rust resistance than the above steels. I should point out that there doesn’t appear to be consensus on what percent of chromium is needed for a steel to be considered stainless.
The de-facto standard
In the cutlery industry, the de-facto standard is 13%, but the ASM Metals Handbooks says “greater than 10%”, and other books cite other numbers. It probably makes more sense to measure stainless ness by the amount of free chromium (chromium not tied up in carbides), because free chromium is what forms the chromium oxide on the blade surface that offers stain resistance. The alloying elements have a strong influence on the amount of chromium needed; lower chromium with the right alloying elements can still have “stainless” performance.
Different classes of stainless steels:-
Common – Knife making steel
Because any particular stainless steel is often heat treated to around the same hardness (i.e., 440C is usually around 57 Rc, ATS-34 is 59-61 Rc, S60V is getting consensus at around 56 Rc, etc.) even by different manufacturers, it’s a bit easier to give a general feeling of the performance you’ll get from different classes of stainless steels, without introducing too many inaccuracies.
Please note, though, that the act of grouping differing steels in classes definitely does oversimplify, and some of these steels might more properly fit between the class it’s in, and the following (or previous) one. In addition, better heat treat can move a steel up in performance significantly.
Last disclaimer: not everyone will agree with the groupings I have here. Whew, all that said, here is a general categorization of stainless steels:
420 and 420J
It represent the low end of stainless steels. They are very stain resistant, and are tough due to being very soft. However, they are also very weak, and not very wear resistant. Generally speaking, expect these steels to lose their edge quickly through abrasion and impaction. They are used in less-expensive knives due to their ease of machining.
Ref – 420 vs. 420J2 Steel Composition Comparison.
440A and its relative peers, 425M, 420HC, 12C27, and 6A are the next group.
They can be hardened more than the previous group, for better strength, and they are more wear resistant, though wear resistance is just getting to the point of acceptability. 440A and 12C27 are the leaders of this group, with solid heat treat both perform okay. 12C27 is said to be particularly pure and can perform very well when heat treated properly. 6A trails those two steels, though with its vanadium content, can take a razor edge. 425M and 420HC trail the rest.
Ref – 440A vs. 425M vs. 420HC vs. 12C27 vs. AUS-6A Steel Composition Comparison.
Gin-1, ATS-55, 8A, and 440C comprise the next group.
These steels will usually be stronger than the previous group, and more wear-resistant. Generally speaking, they retain excellent stain resistance properties, though ATS-55 sticks out here as not particularly stain resistant. 8A is also worth a mention, with some vanadium content, it can take an extremely sharp edge very easily, but is also the weakest and least wear-resistant of this group.
Ref – Gin-1 vs. ATS-55 vs. AUS-8 vs. 440C Steel Composition Comparison.
ATS-34/154CM, VG-10, and S60V are the next group up.
It’s difficult to make generalizations about ATS-34 and 154-CM — they are in such widespread use that heat treat varies widely. These steels provide a high-end performance benchmark for stainless steels, and hold an edge well, and are tough enough for many uses (though not on par with good non-stainlesses). They aren’t very stain resistant, however. VG-10 can be thought of as being like ATS-34 and 154-CM, but doing just about everything a hair better. It’s a little more stain resistant, tougher, holds an edge a little better. And VG-10 has vanadium in it, it’s fine-grained and takes the best edge of this group.
By far the best wear resistance of the group, though consensus is becoming that it should be left around the same hardness as 440C (56ish Rc), which means it will be relatively weak compared to ATS-34, 154-CM, and VG-10, and so it will indent and lose its edge quickly when strength is required. S60V is the winner here when pure abrasion resistance is much more important than edge strength.
Ref – ATS-34 vs. 154CM vs. VG-10 vs. CPM S60V Steel Composition Comparison.
BG-42, S90V, and S30V constitute the next group.
BG-42 has better wear resistance than all the previous knife making steel except for S60V. It is tougher than ATS-34, and more stain resistant. It is wear resistant to the point where it can be difficult to sharpen. S90V represents the ultimate in wear resistance in the steels discussed so far. Also tougher than ATS-34, and more stain resistant. It can be very difficult to put an edge on. It is difficult enough to machine than it is used almost exclusively in custom knives, not mass production knives.
In your buying decisions, you might want to take into account the difficulty of sharpening these steels. S30V backs off on the wear resistance of S90V, but is significantly tougher and easier to sharpen. It is more wear resistant than BG-42. The jury is still out, but it may end up this week’s ultimate high-end all-around stainless steel, due to high performance coupled with easier machinability and sharpen ability than the other knife making steel in this class.
Ref – CPM S90V vs. BG-42 vs. CPM S30V Steel Composition Comparison.
More detail in knife making steel:-
Lower carbon content (<.5%) than the 440 series makes this steel extremely soft, and it doesn’t hold an edge well. It is used often for diving knives, as it is extremely stain resistant. Also used often for very inexpensive knives. Outside salt water use, it is too soft to be a good choice for a utility knife.
Ref – 420 Steel Composition.
420 modified with more carbon, to be roughly comparable to 440A.
Ref – 420HC Steel Composition.
440 A – 440 B – 440C
The carbon content (and hardenability) of this stainless steel goes up in order from A (.75%) to B (.9%) to C (1.2%). 440C is an excellent, high-end stainless steel, usually hardened to around 56-58 Rc, very tough and with good edge-holding at that hardness. 440C was the king of stainless cutlery or knife making steel – stainless in the 1980s, before ATS-34 took the title in the 1990s. All three resist rust well, with 440A being the most rust resistant, and 440C the least.
The SOG Seal 2000 is 440A, and Randall uses 440B for their stainless knives. 440C is fairly ubiquitous, and is generally considered a very good general-use stainless, tougher and more stain resistant than ATS-34 but with less edge-holding and weaker. If your knife is marked with just “440”, it is probably the less expensive 440A; if a manufacturer had used the more expensive 440C, he’d want to advertise that.
The general feeling is that 440A (and similar knife making steels, see below) is just good enough for everyday use, especially with a good heat treat (we’ve heard good reports on the heat treat of SOG’s 440A blades, don’t know who does the work for them). 440-B is a very solid performer and 440-C is excellent.
Ref – 440A vs. 440B vs. 440C Steel Composition Comparison.
425M – 12C27
Both are very similar to 440A. 425M (.5% carbon) is used by Buck knives. 12C27 (.6% carbon) is a Scandanavian steel used often in Finish puukkos and Norwegian knives. 12C27 is said to perform very well when carefully heat treated, due to its high purity. When done right, it may be a slighter better choice than 440A and its ilk.
Ref – 425M vs. 12C27 Steel Composition Comparison.
AUS-6 – AUS-8 – AUS-10 (aka 6A 8A 10A)
Japanese stainless steels, roughly comparable in carbon content to 440A (AUS-6, .65% carbon) and 440B (AUS-8, .75% carbon) and 440C (AUS-10, 1.1% carbon). AUS-6 is used by Al Mar, and is a competitor to low-end steels like 420J2. Cold Steel’s use of AUS-8 has made it pretty popular, as heat treated by CS it won’t hold an edge like ATS-34, but is a bit softer (and therefore weaker) and tougher.
Its a competitor of middle-tier steels like ATS-55 and Gin-1. AUS-10 has roughly the same carbon content as 440C but with slightly less chromium, so it should be a bit less rust resistant but perhaps a bit tougher than 440C. It competes with higher-end knife making steel, like ATS-34 and above.
All 3 steels have some vanadium added (which the 440 series lacks), which will improve wear resistance and refines the grain for both good toughness, and the ability to sharpen to a very keen edge. Many people have reported that they are able to get knives using steels that include vanadium, like 8A, sharper than they can get non-vanadium steels like ATS-34.
Ref – AUS-6A vs. AUS-8A vs. AUS-10 Steel Composition Comparison.
GIN-1 aka G-2
A steel with slightly less carbon, slightly more chromium, and much less moly than ATS-34, it used to be used often by Spyderco in their less-expensive knives. Spyderco has since switched to ATS-55 and 8A, but Benchmade is now using Gin-1 in their less-expensive knives. A very good stainless steel, with a bit less wear resistance and strength than ATS-34.
Ref – Gin-1 Steel Composition.
ATS-34 – 154-CM
ATS-34 was the hottest high-end stainless in the 1990s. 154-CM is the original American version, but for a long time was not manufactured to the high quality standards knifemakers expect, so knifemakers switched over to ATS-34. CPM is again making high-quality 154-CM, and some companies seeking to stick with American-made products (like Microtech) are using it. ATS-34 is a Hitachi product that is very, very similar to 154-CM. Normally hardened to around 60 Rc, it holds an edge very well and is tough enough even at that high hardness. Not as rust resistant as the 400 series above.
Many custom makers use ATS-34, and Spyderco (in their high-end knives) and Benchmade are among the production companies that use it. Contrary to popular belief, both steels are manufactured through the Argon/Oxygen/Decarburization process (AOD), not vacuum remelted.
Ref – ATS-34 vs. 154CM Steel Composition Comparison.
Similar to ATS-34, but with the moly removed and some other elements added. This steel is a good cutlery steel but a tier behind ATS-34 and its closest competitors (other steels in ATS-55’s class might be Gin-1 and AUS-8). With the molybdenum removed, ATS-55 does not seem to hold an edge quite like ATS-34, and reports are that it’s less rust-resistant. My guess is that with the moly gone, more chromium is tied up in carbides — which means less free chromium for rust resistance, and softer chromium carbides replacing moly carbides for less wear resistance.
Ref – ATS-55 Steel Composition.
Another vanadium-containing high-end stainless steel. Due to the vanadium content, VG-10 takes a killer edge, just like other vanadium steels like BG-42 and AUS-8. VG-10 is also tougher and more rust-resistant than ATS-34, and seems to hold an edge better.
Ref – VG-10 Steel Composition.
Vanadium in VG-10 is rather trace amounts, influencing grain refinement, not so much wear resistance. Still, Cobalt and Molybdenum are strong carbide formers, Chromium is also a carbide former. Overall, very good knife making steel, but if you are looking specifically for high wear resistance look elsewhere, with alloys having few % V or Nb, etc.
Bob Loveless announced a while back that he’s switching from ATS-34 to this steel. Keep an eye out for it, it’s bound to catch on, although the higher cost, limited stock-size availability, and added difficulty of manufacturing are holding BG-42’s popularity back. BG-42 is somewhat similar to ATS-34, with two major differences: It has twice as much manganese as ATS-34, and has 1.2% vanadium (ATS-34 has no vanadium), so look for significantly better edge-holding than ATS-34. The addition of vanadium and the clean manufacturing process (VIM/VAR) also gives BG-42 better toughness than ATS-34. Chris Reeve has switched from ATS-34 to BG-42 in his Sebenzas.
Ref – BG-42 Steel Composition.
S60V (CPM T440V) – S90V (CPM T420V)
Two steels that hold an edge superbly, world class type edge holding, but it can be difficult to get the edge there in the first place. These steels are made with Crucible’s particle metallurgy process, and that process allows these steels to be packed with more alloying elements than traditional knife making steel manufacturing methods would allow. Both steels are very high in vanadium, which accounts for their incredible wear resistance. Spyderco offers at least one model in CPM S60V. Spyderco, one major user of S60V, has cut back hardness down to 55-56Rc, in order to keep toughness acceptable, but that sacrifices strength so there is a tradeoff.
S90V is CPM’s follow-on to 440V
With less chromium and almost double the vanadium, is more wear-resistant and tougher than S60V — and, in fact, is probably more wear-resistant than any other stainless steel used in the cutlery industry. As such, S90V is in the running with steels like BG-42 as among the best general-purpose stainless steels; however, S90V is even more expensive and difficult to work than BG-42, so it’s strictly in the realm of custom makers currently.
Ref – CPM S60V vs. CPM S90V Steel Composition Comparison.
The newest stainless steel from Crucible, purpose-designed as a cutlery steel. This steel gives A2-class toughness and almost-S90V class wear resistance, at reasonable hardness (~59-60 Rc). This mix of attributes is making S30V one of the hottest stainless knife making steel going, with makes such as Chris Reeve switching from BG-42 to S30V. Will this be the new king of general-purpose stainless cutlery steels? We’ll know over the next couple of years.
The section about S30V was written when it was just appearing on the market. By now it is not new, was well tested and is used in knife making steel of all varieties. Toughness is nowhere near of A2 steel, and wear resistance, while being quite high, still not on S90V levels either. Very decent knife making steel never the less, just didn’t live pup to all they hype surrounding its development.
Ref – CPM S30V Steel Composition.
400 Series Stainless
Before Cold Steel switched to AUS-8, many of their stainless products were marketed as being of “400 Series Stainless”. Other knife companies are beginning to use the same term. What exactly *is* 400 Series Stainless? I always imagined it was 440-A, but there’s nothing to keep a company from using any 4xx steel, like 420 or 425M, and calling it 400 Series Stainless.
Made by forge-welding two or more different metals (usually steels). The billets are heated and welded; The Damascus is then acid-etched. The different metals etch at different rates, and depth and color contrast are revealed.
Damascus can be made with performance and/or aesthetic objectives in mind. Aesthetically, the choice of materials is important. One shiny steel and one darker steel etch out to show the most striking pattern. If the maker is going more for beauty than performance, he might even go with nickel, which is bright but does not perform as well as steel for cutlery applications. The other factor affecting beauty is of course the welding pattern. Many patterns of Damascus are available today, from random to star to ladder, and a whole lot more.
The following steels will provide bright lines:
L-6 and 15N20 (the Swedish version of L-6) — nickel content
O1 — chromium content
ASTM 203 E — nickel content
The following steels will provide dark lines:
Knife Making Steel Analysis